How To Fix Mustang Convertible Back Window

Download Article

Download Article

Modern soft convertible motorcar tops often have glass windows glued to the material, vinyl or other soft material with a melted plastic strip instead of a clear vinyl window sewn to it. If and when the glass comes unstuck -- sometimes due to the sail shrinking from neglect or otherwise -- information technology can be very hard to reattach. Double-sided foam tape such as 3M VHB tape (what one author used, others could be OK too) tin can reattach them, but should exist applied in a specific fashion to avert abiding strain that volition break its bail.

Steps

1. 1

   Reattach the soft top material ("canvass") to the glass when just role of the sheet has detached so that the drinking glass does non accept to exist re-centered within the pigsty in the sheet. If it does have to exist re-centered i might practice that by measuring distances with the defrosting filigree as a guide and, in any case, holding the drinking glass temporarily in place with gaffer'due south or other mucilaginous record.

2. two

   Open the acme slightly so that it is not taut. Prop something such equally a pocket-size empty box between the front edge of the top and the upper edge of the windshield frame and then that the top stays open slightly.

   Advertisement

3. 3

   Find the seal that was attached only has become unattached, such as the lower edge of the exterior layer of canvas. ^[i] If dirt has accumulated in the pocket that has been exposed to the conditions you may wish to vacuum out any big particles.

4. 4

   If merely a very small-scale part has separated leave it alone. If a large part is mostly separated yous may wish to split up information technology entirely to re-seal it as one continuous slice.^[2]

5. 5

   Make clean the mating surfaces with rubbing alcohol.

6. vi

   Close the roof completely to come across where the sheet falls on the glass when pulled gently flat as far in on the glass as it will go, but not pulled hard. At least in the case of cotton canvass, this will probably be non as far up onto the drinking glass as originally (or as on a still-attached inside layer) considering it volition have shrunk since new.

7. 7

   Re-open up the roof slightly and re-prop it.

8. 8

   Apply a strip of double-sided foam tape such as 3M VHB ("very loftier bond")--cream then that it volition arrange to any irregularities, preferably black so ultraviolet rays will not promptly destroy its exposed border--to the glass with the edge coming up to the betoken you determined previously. ^[3]

9. 9

   Bring the eye of the area beingness attached (such equally the center, left-versus-right-wise of the bottom outside canvas) up to the edge of the tape. Information technology should have simply a petty slack, since it needs to exist pulled basically smooth but not taut when the top is closed. But a little slack when the top is closed is much better than tension, which will unstick the tape.

10. 10

    Stick the canvas to the record, working outward. The reason to work outward from a key betoken is so that whatever "backlog" material does not build up at 1 side.^[4]

11. eleven

    Rub downwards the canvas over the tape firmly and apply some heat--not a smashing painfully hot amount--with a blow dryer for a thorough bond.

    • The convertible pinnacle should exist stock-still.

Advertisement

Add together New Question

• Question

  How much volition it cost to supplant the top with the original window?

  

  I have a 2007 Mustang convertible. The window is separating from the cloth elevation. I went to two convertible meridian/upholstery shops, and both told me the window is oestrus sealed and the entire top needed to be replaced, and both gave me a price of $ane,900.

• Question

  I take in my garage a Corvette convertible with a canvas top in nifty status. The seal effectually the glass rear window has popped, will this procedure work?

  

  I used 3M window weld on our 2004 Volvo C70 top and it worked great! Make sure you get every bit much of the one-time adhesive off as possible. Put the 3M primer on first and let it dry for about 10 minutes. Put a bead (nigh 3/16) of window weld on information technology. Clench information technology in place. I used some paint stirrer sticks & C clamps. Let it sit for about 24 hours. Practise non do this if temperature is beneath 40 degrees F.

• Question

  Where can I go 3M VHB foam tape?

  

  Amazon has information technology in a multifariousness of lengths and widths.

• Question

  Tin can Gorilla glue exist used to attach glass to a convertible canvas summit?

  

  No. I tried it and the heat from sitting in the sun made it crevice and come apart.

• Question

  How much volition it cost to replace a rear window on a convertible Sebring?

  

  The shops volition tell you a new top is needed. Fortunately, the Sebring window lays on pinnacle of the canvas flap rather than hanging from it. People swear past Rhino glue for nigh 20 bucks. I'thousand planning to remove the window, make clean the entire lip that the window edge contacts, put a bead of rhinoceros on information technology and lay the window back in. Removing it completely will let me to position it evenly in the hole since the summit textile has most likely shrunk over the years but if yours is but pulling autonomously in a section you tin can open up the top role way and glue the lip while tension is off.

• Question

  Should I mucilage the inside and the outside of the window?

  

  Brett Gilbert

  Height Answerer

  Yes, if the sail is loose on the inside part of the window, glue it as well.

• Question

  Where can I find instructions that are more specific to the type of car I accept?

  

  Brett Gilbert

  Summit Answerer

  You could contact the manufacturer or a mechanic to run across what they recommend. Usually, though, they will tell y'all to replace the unabridged hood. The mucilage or tape techniques work well for just about any machine.

Enquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

• It may be improve to get the superlative fixed in a mode for whose possible failure someone else such as a dealer will take responsibility. But this is a dandy alternative to replacing the summit.

Advertisement

Things You lot'll Need

• 3M VHB cream tape, blackness

About This Article

Cheers to all authors for creating a folio that has been read 206,030 times.

Did this article help yous?

Source: https://www.wikihow.com/Reattach-Rear-Window-Glass-to-a-Convertible-Car-Top

Posted by: garnerrodn1986.blogspot.com

Share this post